LED tube lights are a great way to brighten up a room, and they’re relatively easy to install. In this blog post, we’ll walk you through the steps of how to install LED tube lights on walls.
What LED tube lights are and what are their benefits?
LED tube lights are a type of lighting technology that is quickly gaining in popularity due to its many benefits. Compared to traditional fluorescent tubes, these lights are brighter and offer more consistent illumination across the entire length of the tube. What’s more, they use significantly less energy than traditional lighting options, helping to reduce overall energy costs and carbon emissions. In addition, LED tube lights do not emit any harmful ultraviolet or blue light rays, making them a safer choice for homes and businesses alike. By choosing LED tube lights, you can enjoy all the benefits of modern lighting technology without sacrificing quality or safety.
The required tools and materials for Install LED Tube Lights on Walls
Installation tools for the tube lights: Screwdriver, Wire cutter, Electricians pliers, Neon tester
- The 15cm screwdriver is:
It has a handle that keeps the electricity from getting to the screws. It comes in many different sizes.
- Wire Cutter 15 cm :
It has two sharp edges that can cut through the wire.
- Electricians Pliers (15cm):
You can use it to cut, twist, and pull wires. Cutting pliers come in a range of lengths from 15 to 30 cms. The handles of the pliers are insulated so that they won’t hurt you if you get shocked by electricity.
- Neon Tester:
It is used to see if the supply is working. Phase wire can be found by putting the tester’s tip on the wire and watching the light glow. The tester comes with a screwdriver, but you should be careful when using it.
The raw materials used to put in a tube light are: Fluorescent tube light, Cable, Holder, Nails
- Light from a fluorescent tube:
It is a lamp that makes a lot of light by turning ultraviolet energy from low-pressure mercury into visible light. The lamp is made up of a glass tube with two electrodes, a coating of activate, phosphor powder, and small amounts of mercury.
- Cables and wires:
Cables and wires are flexible metal strands or rods that come in a variety of lengths and diameters, are sometimes covered, and are often electrically insulated. They are mostly used to hold up structures or carry electricity.
- Holder:
The bulb holder is the mechanical part that holds the light bulb in place and connects it to the electrical system.
- Nail:
Most of the time, it’s made of steel. Even though it can be made of aluminum, brass, and many other metals. Its surface can be coated or plated to make it more resistant to corrosion, make it easier to hold or make it look nicer. Depending on what the nail is used for, the head, shank, and point can all be different shapes.
How to install LED tube lights on walls?
1. Before you begin, turn off the power to the area where you’ll be working. This is important for safety reasons.
2. Next, remove the existing light fixture. If there is no existing light fixture, you’ll need to drill a hole in the wall for the electrical wiring.
3. Once the old fixture is removed, you’ll need to connect the wires from the new LED tube light to the electrical wires in the wall. Make sure that you match up the right wires—typically, green is ground, white is neutral, and black is hot.
4. Now it’s time to install the new LED tube light fixture. Start by threading the wires through the mounting plate, then attach the plate to the wall using screws or drywall anchors. Be careful not to overtighten the screws, as this could damage the fixture.
5. Finally, screw in the LED tube light and restore power to the area. You’re now ready to enjoy your new LED tube light!
You can see more full this video: How to install led tube light
Tips and tricks for a successful installation
FAQs about LED tube lights
Can you put LED lights on painted walls?
It is rare that LED strip lights may cause damage to walls, although this can be affected by a number of other situations. How effectively LED strips adhere to a surface can also be affected by factors such as the tensile strength of its adhesive, the longevity of paint or wallpaper, the amount of time that has passed since they were applied, and the temperature.
Do I need an electrician to install LED lights?
Even more crucially, faulty wiring greatly increases the likelihood of an electrical fire. This is just one of the many reasons why we advocate working with a certified electrician and stress the importance of doing so.
Is installing LED lights easy?
LEDs are sold in large rolls that are simple to install and do not require any prior knowledge or experience with electrical systems. It only takes a little bit of forethought at the beginning to ensure that you buy the appropriate length of LEDs and a power supply that matches, which is all that is required for a successful installation.
Will LED lights peel off paint?
It is possible that you may get concerned about the paint on the wall once you learn that you need to remove the LEDs that are attached to it. In point of fact, because these LEDs are attached to the surface with an adhesive that is specific to this type of light, there is a significant possibility that the paint may come off when the LEDs are removed.
What glue can you use for LED lights?
Silicon glue, which has all of the benefits of PU glue and epoxy glue, is characterized by its excellent resilience to heat and low temperatures, its excellent resistance to yellow degeneration, and its low toxicity. The scent of the glue is pleasant, and the glue will not turn yellow even after prolonged use.
Conclusion
Installing an LED tube light is a great way to update your space and save on energy costs. In this blog post, we walked you through the steps of how to install an LED tube light on a wall. If you have any questions about this process or need help with installation, be sure to contact a qualified electrician—they’ll be able to help you out and ensure that everything is installed correctly and safely. Thanks for reading!
Related articles
How to install t8 led tube light?